"Take-up Unit 500"

Aufwickeleinheit info.JPG Aufwickler vorne.JPG

The Take up Unit 500 is a reliable aide to cut tubes, cables and wiring.

show more

The Take up Unit 500 makes it possible to roll up all cable roller, tube roller and wiring self-sufficient and a unstrained. Between an width from 160 mm and an roller diameter of 500 mm. The infeed is controlled with an compensator, this realizes an individual adaption to each tube or cable possible. With the knob on the forefront it is possible to set up the engine speed continuous.

Technical Data:  
Materials: All standard roller
Roller Width: about 160 mm or customization on request
Roller Diameter: about 500 mm or customization on request
Speed:

about 15 m per minute (depending on roller width). It is possible

to set up the engine speed at the knob on the forefront.

Dimensions:

(L/W/H): 400 x 400 x 450 mm. Weight: 10 kg

Housing: Clean room-compliant design, top made of stainless steel.
Supply 110-220V/ 50-60 Hz; external power supply 24V/5A
Scope of delivery: Basic unit, external, power supply, Operating Instruction English
Accessories Heat resistant VA-rolls, roller, …
Other Special sizes and customizations on request.

 

All specifications arsubject to change without notice.

Tube driller "Kiwi" /"KX-100"

Schlauchborhmaschine Kiwi Schlauchbohrmaschine KIWI mit Linearachse

The KIWI is an automatic PC-controlled tube-drilling machine. All types of tubes can be drilled with the KIWI. Hollow drills guarantee a clean and exact drill bore.

show more

The KIWI is a tube driller to drill all kind of holes in all kind of tube materials. The tube holder is adjusted on customer requirement and can be fast and easy changed. To program the turning speed or the drilling depth, the including software is used. The program can be choose by the knob on the side of the machine. Also the drilling depth can be fine adjusted by the knob. To start the drilling process, choose the program, load the tube and start the drilling by using the footswitch.

 

The Kiwi can optional armed with a linear axis like the KX-100. So the tube-driller is fully PC-controlled and can be connected to a host. The positions of the holes to be drilled can be freely programmed in length and angle using the provided software. The drill feed rate and the drilling depth can also be freely programmed for each individual hole. The PC support makes it possible to create and store a virtually unlimited number of different hole patterns. Every drilled tube can be retrieved from a history. Because there is a user account control you can decide which user can create, delete or change programs.

Technical Data:  
Material:

All standard materials like PA, PE, PU, PTFE, Silicone,…

Drill mounting: Standard precision chuck for drills from 0.1 to 3 mm.
Tube diameter:

Approx. 0.5 - 35 mm or according to the customers' request.

Reproducibility: Length approx. 0.1 mm, angle <1° (depending on tube).
Control: Programming via Windows PC with the enclosed software.
Input:

Start position, position before drilling, turns of driller, Push out position,

V-driller, End position, WaitTime, …

Dimensions without PC:

Kiwi: (L/W/H) 200 x 220 x 350 mm, Weight: 7.5 kg
Kiwi and KX-100: (L/W/H) 260 x 400 x 350 mm, Weight: 11 kg

Housing: Clean room-compliant design, top made of stainless steel.
Connection: DC 24V/70W over extern power supply, USB port.
Scope of Delivery:

Machine, Footswitch (only separate Kiwi), Software, Dongle,

Operating Instructions in English.

Accessories:

Holder for other diameters, driller, hollow core driller, liner axis,

heating unit, exhausting system, PC-Win 7/8 for programming.

Miscellaneous: Special sizes and customizations on request.

 

All specifications arsubject to change without notice.

Cutting machine "Cut Box"

Schneidemaschine Cut Box Waagrecht CUT Box Senkrecht Cut-Box mit Winder 230.JPG

The Cut Box was developed for the cutting of different types of tubes of different lengths and diameters. The cutting of extremely soft tubes and tubes with low Inherent stability is no problem with the Cut Box. Thanks to the precise guidance of both blade and tube, the cutting edges are at right angles, the tube remains in its original shape and the length of the tubes remains constant after the process is complete.

show more

With the Cut Box it is possible to cut tubes with a diameter of approximately 0.5 mm ranging up to about 10 mm. The machine has been developed for cutting tubes made from all standard materials. It is PC controlled and whit the software, which is included; you can program the length, number of pieces, speed and acceleration. Because there is a user account control you can decide which user can create, delete or change programs. It is also possible to use the Cut Box without a PC, the last used program is always stored in the machine.


The tube is fed by a feed roll, which contact pressure could adjust by a regulator. So the form of the tube is widely the same. The feeding speed could be adjusted over a wide range, so all types of tube could be fed exactly. The tube is guided by a bushing that is changed in a few seconds. Whit one bushing could be covered a range of about 5 mm. The blade is fast and easy to change.


The machine is totally closed, so that it is practically impossible to injure someone. The Cut-Box complies with CE regulations.

Technical data:  
Materials: All standard materials - PA, PE, PU, PTFE, silicon…
Tube diameter: Can be set 0.3 to 10 mm over bushing.
Tube guidance: Replaceable bushing.
Length: Freely programmable from approx. 0.5 mm - 50 m, in 0.01 mm steps.
Reproducibility:

Is determined by length, material and feeding of the tube.

Typically 1%.

Drive:

Electro-mechanical design

Control: Controlled over Windows PC by including software.
Input: Length, number of pieces, speed, acceleration, ...

Dimensions without PC:

(L/W/H) 330 x 300 x 130 mm, Weight: 6.5 kg
Raise up high about 300 mm.

Housing: Clean room-compliant design, top made of stainless steel.
Supply: 110-230V/ 50-60Hz; 24V/70W, USB-Interface.
Scope of delivery:

Basic unit, power supply, 2 blades, Software, Dongle,

Operating Instructions in English.

Accessories:

Mounting for guide bushings for other diameters, winder, Knifes,

PC for programming.

Miscellaneous: Special sizes and customizations on request.

 

All specifications are subject to change without notice.

Welding Mashine "HS-IR4"

Schweissmaschine IR 4

IR4 Welding-Device for welding of Hypotubes and Sideports.

show more
Technical Data  
Heating: IR 2 x 50 W emitters
Temperature control: Thermocouple, output control
Cooling: Air
Dimensions: (L/W/H) 250 x 300 x 140 mm, Weight: 10 kg
Housing: Clean room-compliant design, top made of stainless steel.
Connection: 110-230 V/ 50-60 Hz /300 W, Compressed air hose 6-8 bar filtered.
Miscellaneous: Special sizes and customizations on request.

 

All specifications arsubject to change without notice.

Tipforming Mashine "HS-IR5"

HS-IR5

The IR5 can be used to form plastic tips from 0.5 – 7.0 mm diameter. The IR5 can also be used for welding catheter shafts and tips of balloon catheters.

show more

The IR5 has been developed for forming plastic tips with a diameter of 0.5-7 mm. Optimum adaptation to your production can be achieved by quickly and simply changing between different molds, such as glass, metal and plastic molds. The IR5 enables forming of open and closed tips. In addition, the IR5 is an ideal welding machine for catheter shafts and tips of balloon catheters.

 

The IR5 is loaded manually. The tube is inserted into the slide. The tube is clamped and the freely programmable sequence is started by pressing the start key. The following parameters can be entered: Power, start position, tip length, speed and cooling temperature. The process can also be adapted to new requirements in the machine program.

 

The mold is heated by 4 radially arranged IR emitters. It is thus possible to change the mold without the need for readjustment. The mold is exchanged together with the complete mold holder. The time taken is typically << 5 min. The IR sensor is recommended if the temperature can be measured at the tip of the mold (if no through-loading is necessary).

 

Technical Data:  
Materials: All standard materials, ...
Tube diameter: 0.5 to 7 mm
Tube clamping: Pneumatic
Tube guidance: Exchangeable guide bushings
Mold holder: Quick-change aluminium holder for mounting glass, metal and plastic process molds
Length adjustment: Feed programmable in length and speed
Heating: IR 4 x 50 W emitters Temperature up to 300°C
Temperature control:

Thermocouple, output control

Option: Infrared sensor

Cooling: Air
Dimensions without PC: (L/W/H) 400 x 250 x 140 mm, Weight: 9.4 kg  
Housing: Clean room-compliant design, top made of stainless steel.
Connection: 110-230 V/ 50-60 Hz /250 W, Compressed air hose 6-8 bar filtered.
Scope of delivery:

Machine, with thermocouple control and mold holder.

Software, Dongle, Operating Instructions in English.

Accessories: Molds for other diameters, water cooled system, PC-Win 7/8 for programming.
Miscellaneous:        Special sizes and customizations on request.

 

All specifications are subject to change without notice.

"Winder 230"

Winder 230 Winder Serie Winder manuell

The Winder 230 is a reliable aide to cut tubes, cables and wiring.

show more

The Winder-230 makes it possible to roll down all cable roller, tube roller and wiring self-sufficient and a unstrained. Between an width from 100 mm and 230 mm and a weight up to 30 kg. It is possible to adapt the Winder 230 on the carried roller in a few seconds. The infeed is controlled with an compensator, this realizes an individual adaption to each tube or cable possible. With the knob on the forefront it is possible to set up the engine speed continuous.

Technical Data:  
Materials: All standard roller
Roller Width: about 100 bis 230 mm or customization on request
Speed:

about 10 m per minute (depending on roller width). It is possible

to set up the engine speed at the knob on the forefront.

Dimensions:

(L/W/H): 320 x 650 x 380 mm. Weight: 8.2 kg

Housing: Clean room-compliant design, top made of stainless steel.
Supply 110-220V/ 50-60 Hz; external power supply 24V/5A
Scope of delivery: Basic unit, external, power supply, Operating Instruction English
Accessories Heat resistant VA-rolls, roller, …
Other Special sizes and customizations on request.

 

All specifications arsubject to change without notice.