Crimping machine "Crimpmaster 3"

Crimpmaster 3

The Crimpmaster 3 is a programmable crimping machine for fixed crimping of stents onto balloon catheters.

 

show more

The force is transferred to the stent via a 6-way IRIS diaphragm profile. A plastic tube is located between the stent and the IRIS diaphragm, which transfers the force from the diaphragm to the stent without causing damage. Consequently, even coated stents can be crimped. The force is adjusted electronically by a controller. The iris diaphragm can also be automatically offset by an angle of 30°. This enables a virtually 100% radial force application. The tool width of 13mm enables both short and long stents to be crimped without changing the tool. The feed for long stents > 13mm is regulated by a freely programmable control and 0-10 programs can be simply selected with a selector switch. The maximum travel is approx. 120 mm.

 

Advantages of the machine

  • Crimping of coated stents
  • Regulated force -> Reproducible process
  • Different sizes and lengths without changing the tool
  • Freely programmable process sequence
  • Design suitable for clean room
  • Simple operation
Technical Data:  
Travel range: 125 mm
Control: Controlled over Windows PC by including software.
Dimensions without PC: (L/W/H) 380 x 340 x 260 mm, Weight: 13 kg
Housing: Clean room-compliant design, top made of stainless steel.
Supply: 110-230 V/ 50-60 Hz; 24 V /70 W, USB-Interface. Compressed air 6-8 bar, Dry, free from oil and grease.
Scope of delivery: Basic unit, Software, Dongle, Operating Instructions in English.
Accessories: Crimping tool, PC-Win 7/8 for programming.
Miscellaneous: Special sizes and customizations on request.

 

All specifications arsubject to change without notice.

Tension and Friction Tester "DLF-380"

DLF-380

The DLF-380 was developed for testing pull-off and friction forces. The tester can be used as an inline product tester and for development.

show more

The DLF-380 tester is equipped with an automatic clamping device on the right side. This clamp can be used to apply a defined clamping force to two clamping jaws. Thus it is possible to measure stents in the friction on the balloon as well. The pressing force can be set by weights and the surfaces can be quickly replaced by different sizes and shapes. Easier operation with only two buttons enables quick familiarisation in production and easy handling. This device is ideal for many measuring tasks.


For measuring, the part to be tested is placed below the clamp block. Then the plates are lowered carefully with the "Clamp" button. The left side is closed with the mechanic spanner. Pressing the start button builds a tension or pressure on the left side with a carriage, and the force on the right clamp is measured over the path and indicated in a diagram. Comfortable, freely programmable software makes it possible to store and call employee management, batch number and up to 2000 programmes. The device has an error recognition function that indicates when the sample goes from adhesive friction to dynamic friction or if the measuring range or force is exceeded.

 

Technical Data:  
Clamp faces right:

Quick change form for taking up the samples
or fixed clamp. Pressing force can be set through weights.

Spanner left: Mechanic quick spanner can be set
Spanner distance: 380 mm or shorter through additional receptacles
Movement path: Infeed length and speed programmable
Maximum path: 100 mm
Path resolution: approx. 0,5 µm
Force measurement: -+ 25 N
Force resolution: approx. 1 mN (+- 32000 bit)
Control: Controlled over Windows PC by including software.
Dimensions without PC: (L/W/H) 700 x 260 x 200 mm, Weight: 11.5 kg
Housing: Clean room-compliant design, top made of stainless steel.
Connection: 110-230 V/ 50-60 Hz; 24V/70 W, USB-Popt.
Scope of delivery: Basic unit, Software, Dongle, 2 weights, Operating Instructions in English.
Accessories: Weights, PC-Win 7/8 for programming.
Miscellaneous: Special sizes and customizations on request.

 

All specifications arsubject to change without notice.